The “60” in 6010 means 60,000 pounds’ tensile strength (the ability to resist being pulled apart) per square inch. The “1” means it can be run in any position—flat, horizontal, vertical, or overhead. … Both 6010 and 6011 are good electrodes.
What does the 0 stand for in E6010?
E – Stands for Electrode 60 – 60,000 tensile strength. 1 – in all position welding can be done 0 – cellulose.
What setting should my 6010 ROD be on?
The correct current, or amperage, setting primarily depends on the diameter and type of electrode selected. For example, a 1/8-inch 6010 rod runs well from 75 to 125 amps, while a 5/32-inch 7018 rod welds at currents up to 220 amps. The side of the electrode box usually indicates operating ranges.
What do the first two digits of 6010 welding rod mean?
The first two digits represent the resulting weld’s minimum tensile strength, measured in pounds per square inch (psi). … The fourth digit represents the coating type and the type of welding current (AC, DC or both) that can be used with the electrode.
What do welding rod numbers mean?
The first two digits of a 4-digit number and the first three digits of a 5-digit number stand for tensile strength. For example, E6010 means 60,000 pounds per square inch (PSI) tensile strength and E10018 means 100,000 psi tensile strength. The next to last digit indicates position.
What does the 1 stand for in E7018?
The “E” in E7018 electrode indicates a tool used for an arc-welding process. The 70 means it makes welds that are very strong (70,000 psi). The 18 means two things: The “1” means the electrode can be used in any position, and the “18” means low hydrogen and usually DC current.
Do you push or pull the welding rod when stick welding?
Push or pull: Here the rule is simple. “If it produces slag, you drag,” says Leisner. In other words, you drag the rod or wire when welding with a stick or flux-core wire welder. Otherwise, you push the wire with metal inert gas (MIG) welding.
What is the best setting for 7018 welding rod?
In general, the 7018 rod is used with currents up to 225 amps. A rule of thumb is to use 30 amps of current per 1/32 inch of rod diameter.
How do I know what amp to weld at?
The specific amperage to be used depends primarily on the diameter of the electrode. For example, an eighth in diameter electrode welds great between 75 and 125 amps. Whereas a 5/32 diameter electrode can weld optimally at up to 220 amps.
Why does my welding rod keep sticking?
If you’re welding with amperage set too low, your electrode will be especially sticky when striking an arc, the arc will keep going out while maintaining the correct arc length or the arc will stutter. … A sign of too much current is when the electrode becomes hot enough to glow.
What is the easiest welding rod to use?
7018: All position electrode with a thick flux and high iron powder content, which makes it one of the easiest electrodes to use. These electrodes produce a smooth, quiet arc with minimal spatter and medium arc penetration.
What’s the difference between 7018 and 6010 electrodes?
The 7018 is the backbone of structural welding. This rod runs completely different from the 6010 and 6011 rods—it is much smoother and easier. More of a “drag” rod, the 7018 is also referred to as a low-hydrogen, or “low-high,” rod in the field. … For this reason, these rods are used extensively in structural welding.
What is the difference between 6013 and 7018?
While both the wires are mild steel based, the coating on both are very different, the 7018 has a low hydrogen potassium coating whereas the coating on the 6013 is high Titania potassium. The electrodes also differ in yield and tensile strength, the 7018 has higher specifications in both.
Is 7018 Rod AC or DC?
The 7018 welding rods are used for pipe welding and structural steel welding and repair welding. This low-hydrogen, usually DC, all-position electrode can also be used with AC, which not many welders may know. The 7018 provides a good bead appearance and smooth, strong welds. It also works on higher strength steels.
What is the strongest welding rod?
Metal Web News claims that 6011 welding rods are capable of producing welds that feature a 60,000 psi minimal tensile strength. The 7018 welding rods produce stronger welds that feature minimal tensile strengths of 70,000 psi.
What does the 3 in a E6013 Rod mean?
The “60” in E6013 indicates that the weld metal will have a minimum tensile strength of 62000 psi. … In this case the “3” in E6013 tells that it has a rutile potassium based flux coating. The penetration of the electrode is light and it can be used with AC and DC currents.